I&rsquove truly liked the look of acrylic floating frames- they&rsquore modern and that brass components- swoon! But they&rsquore quite expensive. I observed one on West Elm, but it was $180. Nope- that&rsquos above my price range. So I considered I could make my own. I&rsquoll be genuine, I&rsquoll struggled with this Diy acrylic body, but I&rsquoll tell you how to stay away from my faults so you can quickly make a single.
It was a entertaining task! And by the end I was actually delighted to be accomplished with it- lol! But we acquired some cute images collectively and it&rsquos exciting to have a minimal snapshot of this moment in time with my tiny guy. The ideal aspect of this huge photo venture- though it was a ache to do, it was absolutely free! Actually it value me $three to get the twelve pictures printed to 4&Primex6&Prime. Which is practically almost nothing!
In addition to the prints, I believed it&rsquod be enjoyable to consist of paint swatches from my rainbow stairs. This was free and I believed it&rsquod enable tell the color story even more obviously. The hues I grabbed from Dwelling Depot are- 1. Beloved Pink, 2. Shy Smile, 3. Coral Fountain, 4. Lamplit, five. Corn Stalk, six. Frittata, seven. Sparkling Brook, eight. Green Aqua, 9. Mirador, 10. Tinted Ice, 11. Early September, and twelve. Blue Chalk
- 2 items of 18&Primex24&Prime plexiglass (.093 thick)
- Brass Signal Standoffs&ndash I utilised 4 for my body (1 on every single corner). This contains screws and anchors for hanging.
- Art. I used 12 items of three&Primex5&Primary prints. One particular substantial piece of sixteen&Primex20&Primary artwork would be great also
- Glue Dots for keeping the art on the plexiglass
- Drill and comprehensive established of drill bits 
I only needed to buy the plexiglass which was $24 and brass indicator standoffs (they had been $seven) for this task, as well as the $three in art. So I used a full of $34 on this task. Considerably visit the website -effective than the $180 to purchase it new!
I obtained my acrylic sheets at Dwelling Depot. Tip- in advance of I do any job the place I require to get supplies from a components shop, I seem the merchandise up on-line to make confident there&rsquos stock at my retailer. Then I can also observe the aisle and bay the item is on that&rsquos uncovered on the products facts website page. I consider a screenshot of that info or compose it down in the notes area of my mobile phone. This designed it straightforward to obtain the plexiglass.
Right now, acrylic is in a little bit of higher demand from customers since they&rsquore getting made use of for sneeze guards. It was difficult to discover these, so just a heads up that you might have to check Lowes and Household Depot and probably travel to come across some in stock.
For the signal standoffs, the components for the corners, I acquired that on the internet at Amazon. I bought the brass model. They are also obtainable in matte black, polished chrome, and brushed silver. Buy the coloration that&rsquoll will do the job very best for your design so you don&rsquot have to trouble with spray painting it.
Begin by getting the artwork completely ready to body. For me, that seemed like trimming the title and symbol off the paint swatches. I also trimmed my 4&Primex6&Primary prints down to four&Primex5&Primary. That way they properly fit on my 18&Primex24&Primary plexiglass body.
Up coming, it&rsquos time to drill holes into the plexiglass so I could cling it with the signal standoff components. I was anxious about this section. 
To drill the holes, I 1st put painter&rsquos tape on the entrance and again on each parts of plexiglass in the corners. Take note, don&rsquot take away the protecting sheet on the acrylic- go away it on so it doesn&rsquot get scratched up. Each the protective sheet and painters tape will assistance avoid cracks..
Following, mark on the best of the tape the place the holes must go. Mine were being one 1/4&Primary from each individual aspect. I put a scrap piece of wooden less than the acrylic to shield my desk.
The most important detail you want to avoid with this step is cracking the acrylic. So what you do is start with a little drill little bit and then function your way up to a even bigger one. I began with a 1/eight&Key side than 3/sixteen&Key, then one/4&Primary then five/16&Primary, then 3/8&Prime to eventually have a large plenty of hole that the components suit properly. Idea- if you get a thicker piece of acrylic, you&rsquore a lot less most likely to crack the glass.
One more tip- if you have extra than one drill, use it! That saves you time with switching out drill bits. It took me about three minutes to drill out 1 gap. So about 30 minutes between two sheets. For the next sheet, lay the completed sheet on top and then mark the holes by putting a sharpie through the unique gap so they each match up.
Unfortunately, on the extremely final hole that I was drilling, I accidentally cracked the glass with the major drill little bit. It was like it caught on a little something. I was devastated! And so unhappy. In hind sight, I want I experienced tried using the approach in which you heat up a landscaping spike on the stove and melt the plexiglass. This web site has fantastic directions for making the hole.
It&rsquoll price $5 a lot more to do, but it saves a ton of time and irritation. So it&rsquos entirely truly worth it!
Given that I couldn&rsquot uncover any additional sheets of plexiglass within 30 minutes of my household, I made a decision to use what I had and set it on the back again. When they are in inventory, I can buy a new sheet and substitute the damaged a single out.
And now, make guaranteed the holes on the two parts of plexiglass match up and the components can go by way of all four holes. If not, drill out where by is required. 
When the hardware goes on nicely, take out all painter&rsquos tape and the protecting movie off the entrance and back again of the acrylic.
At this place, the plexiglass will be quite messy. To clean it, you&rsquoll want to be super mindful. If you wipe the compact parts of glass that was drilled off, it could scratch the floor. In its place, use a blow dryer on the great location to blow off any compact parts.
Upcoming, use a microfiber fabric and a resolution of h2o and dish soap and wipe down equally surfaces of the acrylic. Then, use a clear towel to wipe off the cleaning soap until finally the plexiglass is clear.
I uncovered it best to lay a clean blanket on my bed and then function on the plexiglass when it was laying down.
Eventually, it&rsquos time to place the art among the two pieces of plexiglass. At initially, I imagined I would be ready to just place the components on and the art would be held up. Nope! I couldn&rsquot get it tight more than enough to keep it up! Dang! So alternatively, I had to use glue dots on the back of every print and paint swatch to hold them in position. 
Now it&rsquos time to hang! So I took my frame to my guest bed room wherever it&rsquoll go about the dresser. Pardon the mess in below, we&rsquore renovating the bathroom right up coming to this place and so there&rsquos containers of tiles and a toilet and self-importance cluttering up the place. You&rsquove acquired to love a massive project!
I held up my body. I experienced it assembled with the hardware set up in the corners. When I understood where by I wanted it, I put minor dabs of toothpaste on the again of the components, appropriate higher than exactly where the screw holes wherever. Then I touched the frame to the wall (though a level was well balanced on top) and the toothpaste acquired transferred to the wall!
That&rsquos wherever I screwed in the back again of the hardware to the wall. One more possibility is to keep up the plexiglass with out the components in it and just mark in which the holes are. Due to the fact you have to make 4 holes in the wall, it&rsquos critical to be precise with this step. The wonderful factor about the components I bought is that it arrives with screws and anchors so that tends to make hanging less difficult. 
After the back again of the components is on, put the two sheets of plexiglass on the hardware and screw the best piece on. At this place, you&rsquore accomplished!
And in this article it is all hung up! You can&rsquot truly see the crack- it&rsquos on the base right hand facet. Primarily, it&rsquos a cute and playful piece of artwork!
I appreciate the modern day frame and how gentle and ethereal it is in this room. Although it&rsquos an reasonably priced project, it&rsquos at least a medium to highly developed degree of Do it yourself. I got really pissed off together the way. But I think with the tips I included in this submit, you can keep away from my issues. 
I preferred to exhibit you this see, it&rsquos correct all around the corner from my rainbow mural. They search so pleasurable future to every other! I&rsquom actually loving the colorful artwork right here. I seldom dangle private photographs, but I like how these are both of those sweet, and get the job done with the coloration story in here. This piece is definitely generating me delighted!
As lots of of you know, in the winter season we lease our residence as an Air BNB. Due to the fact it&rsquoll be a rental, I preferred to consider down the own photographs and switch them out for vibrant floral art. I might actually like it more now!
I made these graphics to match my rainbow shades. I imagined it&rsquod be fun to offer you them as a totally free obtain!
To download the absolutely free printable, just place your name and e-mail in the type down below. You&rsquoll get an electronic mail suitable absent with how to down load. In addition you&rsquoll be subscribed to my weekly e-newsletter! If you&rsquore now subscribed, go right here to download.
What do you think? Do you like it? Would you make one particular? Let me know if you have any queries in the remarks!
This publish includes some affiliate hyperlinks for your comfort. Click right here to browse my comprehensive disclosure coverage.
 
If you really like it, pin it!