This put up about how to make three Effortless Do-it-yourself Floating Picture Frames And How to Reduce Plexiglass is sponsored by The House Depot as component of the #THDProSpective Plan. It also incorporates affiliate one-way links. See policies.
Straightforward Do-it-yourself picture frames are actually 1 of my most requested tutorials and oddly sufficient, right up until now, I didn&rsquot have many to share!
.
I actually developed my dad a big Do-it-yourself personalized picture body as a Christmas reward a pair a long time in the past and shared the tutorial for it here. But it made use of dowels, and a router, and it could have been a minimal a lot more included than most people today are on the lookout for.
So, in this publish, I&rsquom heading to clearly show you how I designed three distinctive design and style Super Simple Do-it-yourself floating image frames with just two basic applications. I&rsquoll also demonstrate you how easy it is to minimize plexiglass for them, much too!
.
So if you&rsquore all set to get making, let&rsquos go! I&rsquove bought the video tutorial in this article and the step by phase down below:
Applications AND Resources:
- Miter saw (or any wood slicing noticed is fantastic&ndashdoesn&rsquot have to be a MITER saw)
- Nail Gun (optional, just can make points a lot quicker)
- Wooden Glue
- ¾&Prime sq. dowels
- 1×2 boards
- ¼&Key x one ⅛&Key lattice trim
- Skinny Plexiglass Sheets
- Ryobi One particular+ HP Slice Off Device (made use of to cut plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in spot of clamps to hold items though wooden glue dries)
- Turn buttons
A Note About FLOATING Photo Frames:
I&rsquom sharing how to make three unique fashion FLOATING photograph frames in this tutorial, but the to start with action to building any of them is cutting the plexiglass to the dimension you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this stage. But since the graphics/images I framed are &ldquofloating&rdquo inside of the body, they&rsquore generally sandwiched involving two items of plexiglass. So plexiglass/acrylic is important to be able to &ldquofloat&rdquo your image.
.
To make points quick to change out in these frames, I also applied these convert buttons&mdashor I contact them twisty tabs&ndashon the back again to keep the plexiglass in area.  
HOW TO Lower PLEXIGLASS
Commonly, I have my local glass shop slice my glass and plexiglass pieces for my projects.  But considering that these plexiglass items will be tiny and different personalized measurements, it would be substantially more affordable, more quickly and less complicated to just slice them myself.
.
I utilised some (about) ⅛&rdquo acrylic sheets from House Depot.  They arrive in several sizes, all the way up to a four×8 sheet.  I just grabbed some 11x14s.
I created some basic graphics on my computer (PicMonkey and Canva are good for this!) and also used a patch that I gained a couple years back at a convention for these frames.  You can use a picture, a poster, fabric, what ever you want to body for this.
.
I laid them out on my sheet how I favored the spacing, then marked where by I wished to slash&ndashno measurements right here&hellipjust eyeballing how I assumed the spacing close to the image looked superior.
Now, I&rsquove used the affordable very little hand knife they declare will lower plexiglass ahead of and it was a horrible experience with really lousy outcomes.  I&rsquove also utilized a jig observed to minimize plexiglass and it melts, gets trapped, then chips or cracks the sheet.
.
So THIS time, I experimented with this new Ryobi 1+ HP Compact Slash Off Device with a plastic slicing blade and was extensively impressed with how brief and clean up the cuts were.
When I initial saw this instrument, I located it sort of weird wanting.  But after I utilized it, I comprehended the concept. 
.
It&rsquos basically a hybrid amongst a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned 90 levels. 
.
It&rsquos compact and light-weight and it&rsquos got a ahead and reverse swap to convert the blade both equally instructions.  It&rsquos also got a variable velocity result in&mdashwhich is great for reducing plastic to assistance avert melting. 
It will come with a plastic and drywall blade, a metallic slash off wheel, and a diamond blade for reducing tile and cement board.  You can discover far more about the new Ryboi 1+ HP minimize off device at the website link here if you&rsquore intrigued.
.
For reducing straight traces on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the steel blade guard from it to make the minimize.  You can skip the straight edge and freehand these cuts, way too if you have a continuous hand. (I don&rsquot haha!)
I did uncover it minimize ideal in this circumstance with the switch in reverse. you could look here seemed to not melt that way.
.
I cut two items similar in size for every item I was framing. Then, I was all set to get started generating the genuine floating picture frames.
Simple Do it yourself FLOATING Photograph Frame Fashion 1
Style one is my own most loved, so I&rsquoll commence with it ????
This certain floating image frame style demands ¾&Primary square dowels and one×2 board. It is basically just a 1×2 wrapped around a square dowel frame.
.
I utilised ¾&rdquo sq. dowels for this and set up my miter noticed to slice 45 degrees.  Now, you don&rsquot have to miter these.  You can leave it on 90 and make butt joints.  You also don&rsquot have to have a MITER noticed for this.  Any noticed that you can reduce quite straight with will do the job great.
.
I generally trimmed four items of square dowel so that when match jointly, they&rsquod be just hardly (like ⅛&Key) even bigger than the plexiglass piece I was putting in it.
I applied wood glue to the corners and nailed them together with brad nails.  If you are affected person, and don&rsquot have a nail gun, only glue and clamp till dry.
.
Just after the glue had dried, I lower to in shape one×2 items with 45 degree mitered corners all around this frame.  Yet again, butt joints are great listed here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s around the edges leaving about ¼&rdquo sticking out the back side of the plexiglass, so that when I put in the two ⅛&Primary plexiglass pieces, it&rsquoll be flush across the again facet of the frame.
Then, I screwed these twisty tabs into the back sides of the body to maintain the plexiglass in spot.  I&rsquoll go back again and clear the sawdust off the plexiglass later on, but for now, I established this off to the facet to make the next body.
Quick Do-it-yourself FLOATING Photo FRAMES Type 2
Style two is a minimal simpler and is created of 1x2s and ¼&rdquo thick by 1 ⅛&Key wide lattice trim.
I began by cutting down the lattice pieces so it would make a frame that the plexiglass would fit Inside.  Again, just like right before, the mitered corners are optional.
After I had this lattice frame minimize, I measured its overall sizing and reduce 1×2 items to make a frame whose in general sizing matched that of the lattice frame. See below one×2 body laying on top rated of lattice frame&ndashthey&rsquore the identical dimensions.
I glued and nailed the 1×2 frame together and clamped till dry. Once again, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps ????
.
Then, I flipped it upside down and glued the lattice frame on to the back again.  I utilised a major object to maintain it in area until eventually it was dry, then, I screwed twisty tabs on the again to hold the plexiglass in position. 
Since the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass pieces are positioned inside of, almost everything need to sit flush throughout the back just like the past body.
All over again, I&rsquoll go again and clear the sawdust off afterwards, but for now, I moved on to the final model frame.
Straightforward Do-it-yourself FLOATING Picture Body Fashion 3
Design three is the exact strategy as style 1, but as an alternative of making use of 1x2s, I made use of ¼&Key x 1 ⅛&Primary lattice trim to maintain the body a tiny thinner and much more minimalist looking.
So, I lower ¾&rdquo sq. dowels to make a frame the same size or a bit larger than the plexiglass I was framing and glued and nailed it together.
Then, I minimize lattice trim to wrap about that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back again aspect of the square dowel frame so that when the two items of ⅛&rdquo plexiglass are set up, it&rsquoll all be flush throughout the again.
.
I didn&rsquot have any brad nails small sufficient to nail this body on, so I simply glued and clamped until eventually it was dry.
If you don&rsquot have clamps, you can use painters tape to kind of wrap all-around the pieces to hold until finally the glue dries OR only use some super glue or CA glue to help maintain items in put till the actual wood glue is remedied.
.
Then, just like the very last two frames, I set up twisty tabs to hold the plexiglass in spot.
FLOATING Picture Body HANGING Solutions
The last step is cleanse up and hanging.  I applied some glass cleaner to cleanse up all the noticed dust, then applied a piece of double sided tape on the again plexiglass piece to make absolutely sure the shots stay in location, then set the frames back alongside one another.
.
To dangle, you can use your standard sawtooth hangers for this.
Or merely spot it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and hold it on a piece of wooden dowel you screwed into the wall.
As you can see, creating photograph frames doesn&rsquot have to be complicated.  This is a excellent newbie undertaking you can deal with with nominal tools and get as innovative as you want. 
.
I in fact hung these graphics up in my desk area to help continue to keep me enthusiastic while functioning alone from property suitable now. So, now that my desk house is comprehensive, I guess I should most likely get back to do the job ????
I hope you&rsquove enjoyed this tiny undertaking.  There are a good deal a lot more coming your way, so be positive to subscribe to my publication underneath so you don&rsquot miss out on out on what&rsquos coming subsequent!
.
And don&rsquot forget to pin this for later!
Until eventually future time, happy making ????